{"id":17536,"date":"2022-06-28T22:07:50","date_gmt":"2022-06-28T15:07:50","guid":{"rendered":"https:\/\/www.makeriot2020.com\/?p=17536"},"modified":"2022-06-28T22:07:56","modified_gmt":"2022-06-28T15:07:56","slug":"robotic-toy-car-part-5","status":"publish","type":"post","link":"https:\/\/www.makeriot2020.com\/index.php\/2022\/06\/28\/robotic-toy-car-part-5\/","title":{"rendered":"Robotic Toy Car – Part 5"},"content":{"rendered":"\n

In this almost post we look at the power distribution PCB for the almost completed Robotic Toy Car. I had many interesting issues to solve here, especially since I did not design my own Lipo battery charger circuit, but used a very useful little commercially available unit instead, the MH-CD42<\/p>\n\n\n\n

Based on a relatively difficult chip to get information on, the module is basically an integrated Lipo charge\/discharge module, with a built-in boost converter that provides 5v at a maximum of 2A current. What makes it special is the ability to simultaneously provide current and voltage, as well as charge the attached LiPo cell at the same time, when connected to an external charger.

It does, however, in my view at least, also have a few serious flaws, the most irritating of these being that it will completely discharge the attached LiPo cell even when completely switched off…<\/p>\n\n\n\n

I have thus tried to stop this issue from occurring by adding a switch in line with the Lipo Cell, a quite obvious solution, but it should not have been needed if the chip functioned as intended… ( As far as I can gather, the module was originally designed to be used in USB power banks. This makes the flaw even more serious, as a self-discharging power bank really defeats the purpose)<\/p>\n\n\n\n

Enough of that though, when it does work, it works great. just remember that you can not apply more than 5.5v DC to the charging input of the module. <\/p>\n\n\n\n

\"\"
The completed Power Distribution and charging module<\/figcaption><\/figure>\n\n\n\n

The Schematic<\/h3>\n\n\n\n

There is actually not a lot going on here, as everything is already on the supplied module. I have just added a charging port, additional power headers for 5v output and ground, as well as direct access to the LiPo Cell output, and a switch header to cut off power to the MH-CD42 when it is not in use.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

The PCB<\/h3>\n\n\n\n

The PCB was manufactured as a 2-layer FR-4 board. The entire top layer is used as a ground plane, and the bottom layer was used for the 5v and Vbat traces, which were made as big as possible to allow for the high current ( up to 2A ) that the unit can supply to a load. <\/p>\n\n\n\n

\"\"
The TOP later of the PCB is a complete ground plane.<\/figcaption><\/figure>\n\n\n\n
\"\"
The BOTTOM Layer caries only power traces for 5v and VBat<\/figcaption><\/figure>\n\n\n\n
\"\"
a 3D Render of the PCB, showing header pins and other connections<\/figcaption><\/figure>\n\n\n\n

It is also worth mentioning that the VBAT pins are NOT 3.3v ( Remember that the LiPo cell can run from 4.2v down to 3.0v depending on the charge. These headers were only placed on the board to provide direct access to the LiPo cell, for use with for example an ADC input or for connection to a dev board that is already fitted with a buck converter or a suitable LDO voltage regulator. <\/p>\n\n\n\n

\"\"
The Actual PCB, as received from PCBWay<\/figcaption><\/figure>\n\n\n\n
\"\"
Top Layer of the PCB<\/figcaption><\/figure>\n\n\n\n
\"\"
Bottom Layer of PCB<\/figcaption><\/figure>\n\n\n\n

Manufacturing the PCB<\/h3>\n\n\n\n


Over the past eight years, PCBWay has continuously upgraded their MANUFACTURING plants and equipment to meet higher quality requirements, and now THEY also provide OEM service<\/a>s to build your products from ideas to mass production and access to the market. <\/h6>\n\n\n\n
\n